can we make it faster like this

- Installation
- Operation
- Troubleshooting
User avatar
sherazi007
B9 Maker
B9 Maker
Posts: 281
Contact:

can we make it faster like this

Post#1 » Sat Mar 18, 2017 8:44 am

hey mike
how are you?
well i have watched that clip and i think you must work on it tooo....
here is the link....
https://www.youtube.com/watch?v=GkrHQcXpgIc
thanks
SHERAZ ATIQE

User avatar
Robert Howle
B9 Creator
B9 Creator
Posts: 6175

Re: can we make it faster like this

Post#2 » Sat Mar 18, 2017 12:18 pm

The only kind of models that can be printed that way have very little total area touching the PDMS at any given time, that is why he uses the lattice type model. Also he says in his narrative that it can be used to print this type of model.

Notice he still had to have the vat make a release move in order for the foundation base to print and not get ripped appart with the lift. Too much surface area for a direct lift.

Also a non castable resin. I don't know that there exists a highly reactive photopolymer that is castable. Those short exposure times would not work with any of the castable b9 resins.

Robert Howle
Dance like nobody's watching!

User avatar
sherazi007
B9 Maker
B9 Maker
Posts: 281
Contact:

Re: can we make it faster like this

Post#3 » Mon Mar 20, 2017 4:53 am

yeah i agree with you robert but we should try this....
when we prints a full ring.... we need 3:30 hours or more time to print a ring....
i am not saying rebuild the software as it is but atleast we would come closer to his software by our jewelry catagory....
means if we need 3:30 hours to print a ring after rebuild the software if it prints in 1:30 hours then its ok with us.... cause you know very well our projector's lamp have being weaker so the printing time will be increasing and increasing more.....
we need save our lamp life....
normally our lamp works fine till 600 hours after that it become weaker be cause of it our print ratio get down to 70%
1 - missing parts....
2 - gauge problems....
3 - supports not parallel...
etc.....
i thinks you guys must work on it......
we need updates of the software....... for our projectors lamp life.....
thanks
if you guys mind then i am sorry but i just says what i feels....
cause i already facing lamp problems....
SHERAZ ATIQE

User avatar
sherazi007
B9 Maker
B9 Maker
Posts: 281
Contact:

Re: can we make it faster like this

Post#4 » Mon Mar 20, 2017 5:02 am

watch this image....
we print like this half ring for saving our time.....
but it also needs 2:30 hours to print these rings....
and one more thing i wants to know printer shows 2:30 hours to print but it completed after 4:30 hours... what is this???
why does the printer dont show the right time????
Attachments
Untitled.jpg
SHERAZ ATIQE

User avatar
perpetual_dreamer
B9 Master
B9 Master
Posts: 817

Re: can we make it faster like this

Post#5 » Mon Mar 20, 2017 5:22 am

sherazi007 wrote:watch this image....
we print like this half ring for saving our time.....
but it also needs 2:30 hours to print these rings....
and one more thing i wants to know printer shows 2:30 hours to print but it completed after 4:30 hours... what is this???
why does the printer dont show the right time????


Regarding print time, I'm wondering if it has anything to do with the computer. My print almost always finishes faster than the stated time. Sometimes as fast a 30 minutes faster.

User avatar
sherazi007
B9 Maker
B9 Maker
Posts: 281
Contact:

Re: can we make it faster like this

Post#6 » Mon Mar 20, 2017 5:57 am

but i dont know why my printer gives me wrong time.....
but it is, since i had b9....
SHERAZ ATIQE

Return to “Software”

Who is online

Users browsing this forum: No registered users and 1 guest

Products
X CLOSE
 

 Printers

  Accessories

  Materials

Close Menu Products Forum